Tekniset tiedot
Notes
General The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration.
General Contact connection method: Crimp connection
Safety note
Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Product properties
Product type Circular connectors (device side)
Sensor type Power
Number of positions 4
No. of cable outlets 1
Shielded no
Coding S
Thread type M12
Insulation characteristics
Overvoltage category III
Degree of pollution 3
Electrical properties
Rated voltage in acc. with IEC 61076-2-101 630 V
Rated surge voltage 6 kV
6 kV AC
Contact resistance ≤ 3 mΩ
Insulation resistance ≥ 100 MΩ
Nominal voltage UN 630 V
Nominal current IN 12 A
Test voltage 6 kV
Material specifications
Flammability rating according to UL 94 V0
Seal material FKM
Contact material CuZn
Contact surface material Ni/Au
Contact carrier material PA
Material for screw connection CuZn alloy, nickel-plated
Conductor material Bare Cu litz wires
Muut tiedot
Tuotenumero 1424139
Pakkausyksikkö 1 Kappaletta
Tuoteavain ABQCEG
Tuotekoodi ABQCEG
GTIN 4046356693417
Paino kappaletta kohti (sis. pakkauksen) 59,9 g
Paino kappaletta kohti (ilman pakkausta) 48,4 g
Tullitariffinumero 85366990
Alkuperämaa DE
Tutustu myös
